UP Your Career Here: AGUP.com/careers

UP Your Career Here: AGUP.com/careers

1570 terraincut mower

TerrainCutā„¢ Front Mower

  • 7-Ironā„¢ PRO Side Discharge or Fastbackā„¢ Rear Discharge Deck
  • Diesel Engine
  • Compatible with select front blade, snow blower and broom attachments
Starting At:


View Product Brochure



Features



Hood open for access to engineHood open for access to engine
3-cylinder, liquid-cooled diesel engine3-cylinder, liquid-cooled diesel engine

The 1500 Series TerrainCut Front Mowers are powered by liquid-cooled, 3-cylinder diesel engines.

These engines feature low levels of exhaust and emissions, reduced noise levels, and excellent fuel economy. They also meet the necessary Environmental Protection Agency (EPA) Tier 4 emissions requirements.

Models 1570, 1575, 1580, and 1585 are biodiesel compatible from the factory up to B20. Model 1550 requires an optional kit to be compatible with B20 biodiesel fuel.

Engine drawing for 1570, 1575, 1580, 1585 shownEngine drawing for 1570, 1575, 1580, 1585 shown
 15501570, 1575, 1580, 1585
FuelDiesel (optional kit permits B20 compatibility)Diesel (B20 compatible)
Power  
     Gross at maximum rpm24.2 hp (17.8 kW), PS37.4 hp (27.5 kW), PS
     Net------
Displacement77 cu in. (1.262 L)100.2 cu in. (1.642 L)
Maximum torque------

Key features of the engine include:

  • Economical cast-in block cylinder design for good cooling and long life
  • Indirect fuel injection (model 1550)
  • Direct fuel injection (model 1570, 1575, 1580, 1585) 
    • Injects fuel directly on top of pistons for more efficient combustion
    • Delivers more horsepower per gallon of fuel
    • Improves starting
    • Develops more horsepower per gallon of fuel; improves starting
  • Aluminum alloy pistons with built-in steel struts are lightweight to reduce connection rod bearing loads and provide good heat transfer characteristics
  • Design permits tighter tolerances and neutralizes expansion of the piston, thereby reducing blow-by gas and noise from the piston slap
  • Higher top rings on the piston and a thinner head gasket greatly reduce the volume of unburned waste gases and increase combustion efficiency
  • Timing gears and injector drive gears utilize helical profile gears to help lower engine noise; gear teeth have a newly designed roll-off profile, giving almost no clash, no noise, and no backlash
  • Fuel filter with replaceable element
  • Full-pressure intake manifold provides quick starts in temperatures down to 0°F (-18°C). (Optional engine coolant heater attachment will assist starting under more extreme conditions.)
  • Auto-bleed fuel system; there is no need to prime the system if the tractor runs out of fuel; the system will self-prime the injection pump, lines and injectors, providing fast fuel recovery
  • Key start and shutoff eliminates fuel shut-off knob; electric solenoid shuts fuel supply off immediately when key is turned off
  • See-through coolant recovery tank permits operator to check coolant level without removing radiator cap
  • Enclosed engine compartment to keep out debris and lower sound levels
  • Sealed radiator compartment to keep trash and debris on outside of hood
  • Excellent torque for plenty of lugging power when operating in tough mowing conditions
  • Full-pressure lubrication for positive lubrication, even when operating on slopes
  • Dual-element, dry-type, replaceable air cleaner completely sealed for effective cleaning
    • 90 percent to 95 percent of dirt ejected before it reaches the paper element
  • Secondary safety element for additional filtering
  • Progressive-type air restriction indicator to let operator know when the filter needs servicing
  • Automotive-type alternator for plenty of charge to the battery and power for accessories 
    • 75 amp for open-station models
    • 95 amp for ComfortCab models
  • Automatic initiation of air heater for easier cold-weather starting
  • Automotive-sensing system tells operator when engine is ready to start
Rear-mounted radiators
Rear-mounted radiators (1550, 1570, 1580)Rear-mounted radiators (1550, 1570, 1580)
Rear-mounted radiators and air conditioner condenser (1575, 1585)Rear-mounted radiators and air conditioner condenser (1575, 1585)
Kanzaki 30-cc transmissionKanzaki 30-cc transmission

A Kanzaki® 30-cc transmission is used for reliable operation.

 

Durability features include the following:

  • High-capacity hydrostatic transmission and heavy-duty transaxle maximize performance and uptime and minimize cost of maintenance. 
  • Charge pump is used to efficiently deliver oil to the transmission.
  • Oil cooler helps maintain optimum transmission oil temperature for superior performance and longer transmission life in the most challenging operating conditions.
  • Maximum forward top speed is 12 mph (19.3 km/h) on the 1550, 1570, and 1575 and 15 mph (24.1 km/h) on the 1580 and 1585.
  • Self-bleeding design helps keep air out of the system.

Kanzaki is a trademark of Kanzaki Kokyukoki Manufacturing Company.

Mechanical rear-wheel drive axleMechanical rear-wheel drive axle

Mechanical rear-wheel drive is available as standard equipment (1575, 1580, 1585) or as a factory-installed option (1550, 1570):

  • On-demand four-wheel drive automatically engages and disengages as needed.
    • Constantly maximizes trimming ability
    • Offers better fuel economy than full-time four-wheel drive 
    • Provides better steering tire wear than full-time four-wheel drive 
    • Increases traction and trimming ability to allow a novice operator to mow like an expert
    • Works in the forward direction only
  • Full-time four-wheel drive is on at all times.
    • Can be engaged or disengaged on the go
    • Provides maximum traction and flotation in poor conditions
    • Works in reverse as well as the forward direction
  • Two-wheel drive position is available on 1580 and 1585 with two-speed transaxle.
    • Disengages rear axle when transporting at high ground speeds
High-strength, tubular steel frame High-strength, tubular steel frame

The revolutionary tubular, high-strength welded steel frame provides durability and allows major components to be located lower in the machine:

  • The design results in a lower center of gravity for better stability and traction on hillsides and slopes.
  • Rollover protective structures (ROPS) are integral members of the frame.
Durable design

Durability features of the frame include:

  • Heat-treated cast-iron axles with 1.24-in. (3.15-cm) kingpins
  • Internal wet-disk brakes
  • Hydraulic PTO clutch, with brake
    • Provides smooth engagement and long life
  • Hydrostatic oil cooler
  • O-ring seal (ORS) hydraulic fittings
  • Integrated, shaft-driven power take-off (PTO)
  • Sealed relays and electrical connectors
  • Heavy-duty, dual hydraulic cylinders
  • Nodular cast-iron lift arm sockets
  • Cast-iron rear bumper
1570 Front Mower mowing tall grass1570 Front Mower mowing tall grass
1550 Front Mower1550 Front Mower

Maneuverability:

  • Turn radius of 13 in. (33 cm)
  • Uncut circle of 28 in. (71.1 cm) with a 72-in. (183-cm) 7-Iron™ PRO mower deck
  • Deck offset and pulled rearward 
  • Tail-follows-the-trail trimming capability with 72-in. (183-cm) side-discharge mower deck
  • Steered wheels (tail) stay within the path (trail) cut by the mower deck, allowing maneuverability without the rear of the machine contacting mowing obstacles
Operator controlsOperator controls
Master stop brake/directional foot pedalsMaster stop brake/directional foot pedals

Hydrostatic power steering provides the following benefits:

  • Makes it easy to turn the unit, for less operator fatigue
  • Allows quick turns - two turns lock to lock - for excellent productivity

The steering console offers the following:

  • Throttle
  • Key switch
  • Headlight switch
lift and drive controls and lever for single-spool auxiliary hydraulic kit (1570 shown)lift and drive controls and lever for single-spool auxiliary hydraulic kit (1570 shown)
Controls, including levers for double-spool auxiliary hydraulic Kit (1585 shown)Controls, including levers for double-spool auxiliary hydraulic Kit (1585 shown)

Console information/warning lights include the following:

  • Hourmeter
  • Battery discharge light
  • Engine oil pressure
  • Engine coolant temperature
  • Hydraulic oil over temperature
  • Air preheater
  • Lights
  • Power take-off (PTO) operation indication
  • T4 display for monitoring performance (1570, 1575, 1580, 1585)
1550 Front Mower1550 Front Mower

Two-pedal foot control:

  • Allows operator to select speed and direction with just the touch of a toe
  • Keeps both hands free for steering and operating controls

 

Master stop brake (parking brake):

  • Provides stopping power to both drive wheels
  • Disengages the power take-off (PTO)
  • Disengages the optional cruise control
  • Used also for a parking brake
Individual turn-assist brakes and differential lockIndividual turn-assist brakes and differential lock

Individual turn-assist brakes:

  • Provides additional traction when operating on hillsides
  • Ideal for tight trimming situations
  • Work in conjunction with hydrostatic foot controls to stop or slow the unit for turns

Differential lock:

  • Locks both of the front drive wheels together for added traction
  • Easily engaged with the left foot
Four-wheel-drive leverFour-wheel-drive lever
Deck lift-control leverDeck lift-control lever

Four-wheel drive (4WD) control lever (standard on 1575, 1580, and 1585; factory-installed option on 1550 and 1570)

 

The 4WD control lever:

  • Allows the operator to select between on-demand or full-time four-wheel drive (4WD) on 1550, 1570, and 1575 models (factory-installed option on 1550 and 1570)
  • Allows the operator to select between on-demand or full-time four-wheel drive (4WD) and full-time two-wheel drive (2WD) on 1580 and 1585 models

Electronic cruise control (optional):

  • Beneficial when mowing open areas or when transporting

Lift-control lever is conveniently located, within easy reach of the operator's right hand.

1585 shown with control levers for double-spool auxiliary hydraulic kit1585 shown with control levers for double-spool auxiliary hydraulic kit
#

Two-speed transaxle shift lever is standard on 1580 and 1585.

Safety starting system

TerrainCut™ Front Mowers have an operator-presence system.

 

To start the engine the following conditions must be met:

  • Master brake must be depressed or the parking brake locked; the hydrostatic foot controls will then be in the neutral position.
  • PTO must be disengaged
  • Ignition key must be used.

In addition, once the engine is running, an interlock automatically shuts the engine and PTO off if the operator leaves the seat. To keep the engine running, the operator must disengage the PTO and set the parking brake before dismounting.

Since 1998 the John Deere 7-Iron™ mower deck has demonstrated commercial quality, performance, and durability. The 7-Iron PRO, Fastback™, and V-Flex mower decks deliver an even higher-quality cut in even more diverse conditions.

1580 Front Mower1580 Front Mower
1585 Front Mower1585 Front Mower
#

TerrainCut Commercial Mower Compatibility

 

Mower Deck 15501570157515801585
60-in. (152-cm) 7-Iron PRO Side-Discharge Mower DeckXXX*X*X*
62-in. (157-cm) Fastback Rear-Discharge Mower DeckXXXXX
72-in. (183-cm) 7-Iron PRO Side-Discharge Mower DeckXXXXX
72-in. (183-cm) Fastback Rear-Discharge Mower DeckXXXXX
72-in. (183-cm) 7-Iron V-Flex Side Discharge Mower Deck XXXX

Rear weights (R66949) are required based on machine configuration. Must also order TCB10303, rear weight mounting bracket.

*Mower deck offset for trimming capability. Vehicle track width is 2 in. (5.1 cm) wider on the discharge side of deck. This may cause the tire to drive over uncut grass on discharge side of deck.

NOTE: These mower decks will not retrofit to F900 Series or F1145 Front Mowers.

Rotate for Service (RFS™)
Mower deck showing RFS featureMower deck showing RFS feature
#

Rotate for Service (RFS) feature provides access for cleaning and maintenance of the mower decks:

  • The rotation angle will vary depending on deck size and power unit tire size.
  • No tools are required to access belts.
  • The underside of the mower deck is easy to access.
  • Easy on/off design simplifies installing and removing mower decks.
  • Top, greaseable spindles can be accessed without removing belt covers.

The Rotate for Service position also reduces the length of the machine for trailering.

Certification

TerrainCut Front Mowers comply with ANSI B71.4 safety certification.

Heavy-duty blade spindles
Cast-iron spindle housingCast-iron spindle housing
Cast-iron spindle housingCast-iron spindle housing

The mower spindle housings are made of ductile cast iron, except for the 72-in. (183-cm) 7-Iron V-Flex Side-Discharge Mower Deck, which has an aluminum center spindle housing and cast-iron gearboxes to drive the outer blades.

Key benefits of ductile cast-iron spindle housings:

  • Ductile cast-iron material provides superior impact strength.
  • Gusseted design puts reinforcement where it is needed.
  • Strength of cast iron protects against damage from blade impacts.
  • Grease fitting is mounted at the top for easy access.
  • Grease pressure-relief valve minimizes seal damage from overfilling with grease and keeps debris from entering housing.
  • The 8-in. (20.3-cm) diameter housing distributes loads and impacts to minimize deck-shell damage.
  • Spindle allows ability to be rebuilt.

NOTE: The 72-in. (183-cm) 7-Iron V-Flex Side-Discharge Mower Deck has an aluminum center spindle housing. The outside blades are driven by cast-iron gearboxes.

62-in. (157-cm) Fastback Mower Deck
62-in. Fastback Mower Deck62-in. Fastback Mower Deck
#

The 62-in. (157-cm) Fastback rear-discharge mower is ideally suited for:

  • Areas where people are present
    • Schools
    • Parks
    • Playgrounds
    • Traffic areas (city boulevards, roadsides, etc.)
  • Conditions and applications:
    •  Areas with long grass and weeds
    • Areas where customer is not as concerned about having a wide dispersal of grass (park areas, roadsides, etc.)
  • Government bids that specify a rear discharge mower. 

Key features of the 62-in. (157-cm) Rear-Discharge Mower Deck include: 

  • Mower deck is constructed of 7-gauge, 0.179-in. (4.6-mm) steel for the strength to stand up to the demanding use of commercial and municipal mowing applications.
  • Blade spindle housings are made of ductile cast iron.
    • Gusseted design puts reinforcement where it is needed.
  • Deck is constructed with a patented baffling system that reduces clumping and windrowing and
    produces a finished appearance that competitive rear-discharge mowers cannot match.
  • The belt-drive system has an easy-to-adjust tension device.
    • By using a spring system, the risk for over tensioning is eliminated, ensuring a long belt life and excellent performance during the season.
  • For easy service and maintenance, the deck can be rotated into the vertical locked service position.
  • Deep-deck design increases airflow so more material can be processed.
  • Operator can trim with either side.
    • Dual side trimming increases operator productivity.
  • 1-in. to 6-in. (2.5-cm to 15.2-cm) cutting heights, in 0.5-in. (1.3-cm) increments, allow the operator to match all mowing conditions.
  • Gauge wheels, rollers, or side-mounted skid shoes lift the deck over uneven surfaces for a well-groomed appearance.
  • Double-captured anti-scalp wheels provide increased durability.

  • Easy lift and lock system for service purposes.

  • Standard semi-pneumatic caster tires will not go flat when punctured.

  • Spindles can be greased without removing belt shields.
  • 1-in. (2.5-cm) cold-forged spindles are strong for long life.
    • Heat-treated to provide additional strength
  • Certified to European (CE) standards
72-in. (152-cm) 7-Iron PRO Side-Discharge Mower Deck
72-in. 7-Iron Pro Side-Discharge Mower Deck72-in. 7-Iron Pro Side-Discharge Mower Deck
#

Features include:

  • Blade tip speed of 18,000 fpm (5486 m/min) for more blade strikes per inch mowed.
  • Redesigned front baffle manages airflow and controls clippings better.
  • Spindle pocket reinforcement gives even greater structural durability.
  • Blade spindle housings are made of ductile cast iron.
    • Gusseted design puts reinforcement where it is needed.
  • Adjustable anti-scalp wheels help smooth out the mowing job.
  • Standard semi-pneumatic caster tires will not go flat from punctures.

The mower is designed to provide exceptional cut quality at higher travel speeds:

  • The mower deck is stamped from 7-gague, 0.179-in. (4.6-mm) steel to minimize the number of welds and provide a smooth underside, with fewer sharp corners, for reduced material buildup.
    • Provides precision components and long deck life
    • Single piece of steel means no welds to break
    • Provides a smooth underside, without corners, reducing material buildup
  • 0.75-in. (1.9-cm) solid steel bar is welded to mower deck perimeter for added strength.
  • The rounded corners of the stamped deck help distribute impact stress to reduce the potential of damage when the mower contacts trees, rocks, curbs, and other fixed obstacles.
  • A deep-deck design of 5.5-in. (14-cm) delivers excellent airflow so material can be processed quickly and efficiently.
  • 1-in. to 6-in. (2.5-cm to 12.7-cm) cutting heights, in 0.5-in. (1.3-cm) increments, allow the operator to match all mowing conditions.

Unique baffling system allows grass to stand up before being cut, producing a uniform length and appearance:

  • Baffling system eliminates clumping, blowout, and windrowing.
  • Wide discharge opening provides even clipping dispersal for an excellent, finished appearance in all conditions.
72-in. (183-cm) Fastback Mower Deck
72-in.  Fastback Mower Deck72-in. Fastback Mower Deck
#

The 72-in. (183-cm) rear-discharge mower deck is ideally suited for:

  • Areas where people are present
    • Schools
    • Parks
    • Playgrounds
    • Traffic areas (city boulevards, roadsides, etc.)
  • Conditions and applications:
    • Areas with long grass and weeds
    • Areas where customer is not as concerned about having a wide dispersal of grass (park areas, roadsides, etc.)
  • Government bids that specify a rear discharge mower.

Key features of the 72-in. (183-cm) Rear-Discharge Mower Deck include:

  • Mower deck is constructed of 7-gauge, 0.179-in. (4.6-mm) steel for the strength to stand up to the demanding use of commercial and municipal mowing applications.
  • Blade spindle housings are made of ductile cast iron.
    • Gusseted design puts reinforcement where it is needed.
  • Deck is constructed with a patented baffling system that reduces clumping and windrowing and
    produces a finished appearance that competitive rear-discharge mowers cannot match.
  • The belt-drive system has an easy-to-adjust tension device.
    • By using a spring system, the risk for over tensioning is eliminated, ensuring a long belt life and excellent performance during the season.
  • For easy service and maintenance, the deck can be rotated into the vertical locked service position.
  • Deep-deck design increases airflow so more material can be processed.
  • Operator can trim with either side.
    • Dual side trimming increases operator productivity.
  • 1-in. to 6-in. (2.5-cm to 15.2-cm) cutting heights, in 0.5-in. (1.3-cm) increments, allow the operator to match all mowing conditions.
  • Gauge wheels, rollers, or side-mounted skid shoes lift the deck over uneven surfaces for a well-groomed appearance.
  • Double-captured anti-scalp wheels provide increased durability.

  • Easy lift and lock system for service purposes.

  • Standard semi-pneumatic caster tires will not go flat when punctured.

  • Spindles can be greased without removing belt shields.
  • 1-in. (2.5-cm) cold-forged spindles are strong for long life.
    • Heat-treated to provide additional strength
  • Certified to European (CE) standards
72-in. (183-cm) 7-Iron V-Flex Commercial Side Discharge Mower Deck
72-in. 7-Iron V-Flex Deck72-in. 7-Iron V-Flex Deck
#

The 72-in. (183-cm) 7-Iron V-Flex Mower Deck is suitable for those who need a rotary deck capable of following the undulations and mounding in rough or uneven areas: 

  • Golf courses
  • Sports facilities
  • Parks and recreation facilities
  • Municipalities 

The V-Flex deck is constructed of 7-gauge, 0.179-in. (4.6-mm) steel:

  • Added strength to stand up to the demanding uses on the golf course. 

The deck has a patented vertical belt drive system, which allows for the deck to articulate 20 degrees above and below center. This design also allows for belts to stay clean and prevents the belt from stretching and twisting when flexing.

Mower deck specifications

 

 60-in. (152-cm) 7-Iron PRO Side-Discharge62-in. (157-cm) Fastback Rear-Discharge72-in. (183-cm) 7-Iron PRO Side-Discharge72-in. (183-cm) Fastback Rear-Discharge72-in. (183-cm) 7-Iron V-Flex Side-Discharge
Gauge (thickness)7 gauge, 0.179 in. (4.6 mm)7 gauge, 0.179 in. (4.6 mm)7 gauge, 0.179 in. (4.6 mm)7 gauge, 0.179 in. (4.6 mm)7 gauge, 0.179 in. (4.6 mm)
Cutting height1 to 6 in.  (2.5 to 15.2 cm)1 to 6 in.  (2.5 to 15.2 cm)1 to 6 in.  (2.5 to 15.2 cm)1 to 6 in.  (2.5 to 15.2 cm)1 to 6 in.  (2.5 to 15.2 cm)
Caster wheel typeSemi-pneumaticSemi-pneumaticSemi-pneumaticSemi-pneumaticPneumatic
Gauge wheelsYes, front and rearYes, front and rearYes, front and rearYes, front and rearYes, front and rear
Deck oscillation relative to ground plane+/- 15 degrees+/- 15 degrees+/- 15 degrees+/- 15 degrees+/- 15 degrees
Lateral deck tilt+/- 8 degrees+/- 8 degrees+/- 8 degrees+/- 8 degrees+/- 8 degrees
Deck installed at factoryNoNoNoNoNo
Time required for one person to install or remove deck (without tools)10 minutes10 minutes10 minutes10 minutes10 minutes
Time to change height of cut3 minutes without tools3 minutes without tools3 minutes without tools3 minutes without tools3 minutes without tools
Belt typeKevlar beltKevlar beltKevlar beltKevlar beltKevlar belt
Belt shield typePlasticPlasticPlasticPlasticPlastic
Belt shield time to remove or install2 minutes or less2 minutes or less2 minutes or less2 minutes or less2 minutes or less
Blade typeHigh liftMedium liftHigh liftMedium liftHigh lift
Blade tip speed18,000 fpm (5,486 m/min)16,000 fpm (4,877 m/min)18,000 fpm (5,486 m/min)16,000 fpm (4,877 m/min)16,800 fpm (5,122 m/min)
Spindles33333
Spindle-housing materialDuctile cast ironDuctile cast ironDuctile cast ironDuctile cast ironCenter - aluminum, outside - cast-iron gearbox
Deck level laterally when raisedYesYesYesYesYes
DischargeSideRearSideRearSide
Mowing width60 in. (152 cm)62 in. (157 cm)72 in. (183 cm)72 in. (183 cm)72 in. (183 cm)
Overall width (chute down)74 in. (188 cm)64 in. (163 cm)86 in. (218 cm)74 in. (188 cm)86 in. (218 cm)
Weight---------------
60-in. (152-cm) 7-Iron PRO Side-Discharge Mower Deck
60-in. 7-Iron PRO Mower Deck60-in. 7-Iron PRO Mower Deck
60-in. 7-Iron PRO Mower Deck60-in. 7-Iron PRO Mower Deck

Features include:

  • Blade tip speed of 18,000 fpm (5486 m/min) for more blade strikes per inch mowed.
  • Redesigned front baffle manages airflow and controls clippings better.
  • Blade spindle housings are made of ductile cast iron
    • Gusseted design puts reinforcement where it is needed.
  • Spindle pocket reinforcement gives even greater structural durability.
  • Adjustable anti-scalp wheels help smooth out the mowing job.
  • Standard semi-pneumatic caster tires will not go flat from punctures.

The mower is designed to provide exceptional cut quality at higher travel speeds:

  • The mower deck is stamped from 7-gauge, 0.179-in. (4.6-mm) steel to minimize the number of welds and provide a smooth underside, with fewer sharp corners, for reduced material buildup.
    • Provides precision components and long deck life
    • Single piece of steel means no welds to break
    • Provides a smooth underside, without corners, reducing material buildup
  • 0.75-in. (1.9-cm) solid steel bar is welded to mower deck perimeter for added strength.
  • The rounded corners of the stamped deck help distribute impact stress to reduce the potential of damage when the mower contacts trees, rocks, curbs, and other fixed obstacles.
  • A deep-deck design of 5.5-in. (14-cm) delivers excellent airflow so material can be processed quickly and efficiently.
  • 1-in. to 6-in. (2.5-cm to 12.7-cm) cutting heights, in 0.5-in. (1.3-cm) increments, allow the operator to match all mowing conditions.

Unique baffling system allows grass to stand up before being cut, producing a uniform length and appearance:

  • Baffling system eliminates clumping, blowout, and windrowing.
  • Wide discharge opening provides even clipping dispersal for an excellent, finished appearance in all conditions.
Deluxe comfort seatDeluxe comfort seat

Operator comfort enhances productivity. The open station TerrainCut™ Front Mowers can be equipped with three seat options that have features and adjustments to make most any operator comfortable.

 

Deluxe comfort seat

  • Seat with fore-aft adjustment to accommodate both tall and short operators
  • Standard adjustable armrests

Other comfort features include:

  • Standard cup holder
  • Noise level meets North American and European standards

Two factory-installed seat options are available for extra comfort for long-day productivity.

Engine hood
Large screened area of engine hoodLarge screened area of engine hood
Hood latchHood latch

Engine hood includes large screened area:

  • Minimizes the amount of material that can get to the cooling radiators
  • Minimizes the need to clean the hood screens 

Hood latch keeps the hood securely in place, providing an optimum seal:

  • A single hood latch is located on top of the hood behind the seat.
Engine hood opens to the rearEngine hood opens to the rear
Designed-in service accessibilityDesigned-in service accessibility

Designed-in service accessibility helps ensure daily maintenance is completed to keep the machine operating at peak performance.

 

The hood opens rearward, exposing the following:

  • Engine
  • Oil and fuel filter
  • Hydraulic oil cooler
  • Radiator check/fill

The hood can be totally removed, if necessary. The seat flips forward for access to air filter, fuse bank, engine oil dipstick, and front of engine.

Condenser release knobCondenser release knob
Condenser tilted back to permit cleaningCondenser tilted back to permit cleaning

Easy-to-turn knobs are provided to release the air conditioning condenser (1575 and 1585 only) and fuel and hydraulic oil coolers so they can be tilted back to permit thorough cleaning between them and the engine coolant radiator.

Foot platform access panel
Removable foot platformRemovable foot platform
#

The panel on the foot platform can be removed for access to the transaxle, PTO shaft, and most linkages.

 

Easy-to-read daily service decal is located on the bottom of the foot platform panel:

  • Provides access to easily hook up driveshaft when changing implements
  • Makes it more likely service will be performed at the optimum time, thus ensuring the highest level of performance and uptime
Panel on foot platform removedPanel on foot platform removed
#

Removal of the foot platform gives convenient access to the driveshaft that powers the mower deck, snow blower and rotary broom:

  • Helps make changing from one front implement to another easier and more convenient

 Hydraulic hoses have reusable O-ring seal (ORS) fittings:

  • ORS fittings seal at a lower torque to prevent leaks.
  • Fittings can be removed from a damaged hose and installed on another hose.
  • Downtime and cost for repairs are reduced considerably.
Rotate For Service™ (RFS) feature shownRotate For Service™ (RFS) feature shown
RFS service lockout latchRFS service lockout latch

RFS feature provides access for cleaning and maintenance of the mower decks:

  • The service-latch pin allows mower deck to lock into position to ensure deck is held in position for cleaning or service.
  • The top-greaseable spindle grease fittings can be accessed without removing the belt covers. 

Front mowers must be properly ballasted for both good performance and safe operation. Ballast requirements differ depending on the front mower model and the implement being used.

The chart below gives the minimum ballast requirements for the various product configurations. Additional ballast is recommended for operating on slopes or other conditions that may warrant it.

NOTE: Use only implements and accessories recommended by the manufacturer.

 Front mowers and current (model year 2015 and later) implements

TerrainCut™ 1500 Series Front Mowers
Product Configuration60-in. (152-cm)
Side-Discharge Deck (7-Iron™ PRO)
 
72-in. (183-cm)
Side-Discharge Deck (7-Iron PRO)
62-in. (157-cm)
Rear-Discharge
Mower Deck
72-in. (183-cm)
Rear-Discharge Mower Deck
72-in. (183-cm) 7-Iron V-Flex Deck60-in. (152-cm) HD Front Blade47-in. (119-cm) HD Two-Stage Snow Blower60-in. (152-cm) HD Two-Stage Snow Blower 60-in. (152-cm) Rotary Broom43-in. (109-cm) Drop Spreader (Order Zone)
1550 Front Mower 2WD1*2*1*2*NA***02*3*1*NA***
1550 Front Mower 4WD01*01*NA***02*2*0Wide track
1570 Front Mower 2WD1*2*1*2*6*02*3*1*NA***
1570 Front Mower 4WD01*01*6*02*2*0Wide track
1575 Front MowerNarrow track + 4 *Wide track + 5*Narrow track + 1 wheel weight
on each side**
+ 3 weights* 
or wide track
+ 3 weights*
Wide track + 6*Wide track + 6*1*NA***6*Wide track + 1 wheel weight on each side** + 3 weights*With 60-in. Rotary Broom: wide track + 2 wheel weight on each side**
or
with 60-in. Snow Blower: wide track
1580 Front Mower01*01*6*0NA***2*0Wide track
1585 Front MowerNarrow track + 4*Wide track + 5*Narrow track + 1 wheel weight
on each side**
+ 3 weights* 
or wide track
+ 3 weights*
Wide track + 6*Wide track + 6*1*NA***6*Wide track + 1 wheel weight on each side** + 3 weights*With 60-in. Rotary Broom: wide track + 2 wheel weight on each side**
or
with 60-in. Snow Blower: wide track
1400 and 1500 Series II Front Mowers
1420 Series II Front Mower  2* 1*4*  NA***6*  4* 6*6* NA*** 
1435 Series II Front Mower 2* 1* 4* NA***6*  4* 6*6* NA*** 
1445 Series II Front Mower 2* 1* 4* 6*6*  4* 6*6* NA*** 
1545 Series II Front Mower 2* 1*4*  6* 6* NA*** 6*6* NA*** 
1565 Series II Front Mower0 2* 1* 4* 6*6*  NA*** 6* 6*NA***
1575/1585 Cab models: Rim design allows for tire assembly to be mounted in two different configurations, a narrow track or wide track width to meet ballast requirements.
*42-lb (19-kg) (R66949) Quik-Tatch weight (installation requires TCB10303, rear weight mounting kit).
**50-lb (23-kg) front wheel weight(s) required (installation requires BM17985, mounting hardware kit).
***NA - Not recommended for use on front mower.
NOTE: Ballast requirements may change. Always refer to the implement owner's manual for the appropriate ballast requirements. 

 Front mowers and model year 2014 and prior implements

1400 and 1500 Series II Front Mowers
Product Configuration60-in. (152-cm) Side-Discharge Deck (7-Iron™ and
7-Iron II)
  
72-in. (183-cm) Side-Discharge Deck (7-Iron and 7-Iron II)62-in. (157-cm) Rear-Discharge
Mower Deck
72-in. (183-cm) Rear-Discharge
Mower Deck
72-in. (183-cm)7-Iron V-Flex DeckMCS 600 Hydraulic DumpSoft
cab
Hard cab60-in. (152-cm) HD Front Blade47-in. (119-cm) HD Two-Stage
Snow Blower
60-in. (152-cm) HD Two-Stage
Snow Blower
60-in. (152-cm) Rotary Broom
1420 Series II Front Mower01*01*NA0006*4*6*6*
1435 Series II Front Mower01*01*NA0006*4*6*6*
1445 Series II Front Mower01*01*3*0006*4*6*6*
1545 Series II Front MowerNA1*NA1*3*0006*NA6*6*
1565 Series II Front MowerNA1*NA1*3*0006*NA6*6*
1500 TerrainCut Front Mowers
1550 Front Mower 2WD1*2*1*2*NANANANA02*3*1*
1550 Front Mower 4WD1*01*NANANANA02*2*0
1570 Front Mower 2WD1* 2*1*2*6*NANANA02*3*1*
1570 Front Mower 4WD1*01*6*NANANA02*2*0
1575 Front MowerNarrow track + 4*Wide track + 5*Narrow track 1 wheel weight on each side**
+ 3 weights* or wide track + 3 weights*
Wide track + 6*Wide track + 6*NANANA1*  NA 6*Wide track 1 wheel weight on each side** + 3 weights*
1580 Front Mower01*01*6*NANANA0NA2*0
1585 Front MowerNarrow track + 4*Wide track + 5*Narrow track 1 wheel weight on each side**
+ 3 weights* or wide track + 3 weights*
Wide track + 6*Wide track + 6*NANANA1*NA6*Wide track 1 wheel weight on each side** + 3 weights*
1575/1585 Cab models: Rim design allows for tire assembly to be mounted in two different configurations, a narrow track or wide track width, to meet ballast requirements.
* 42-lb (19-kg) (R66949) Quik-Tatch weight (requires TCB10303, rear weight mounting kit).
** 50-lb (23-kg) front wheel weight(s) required (installation requires BM17985, mounting hardware kit).
NA - Not recommended for use on front mower.
NOTE: Ballast requirements may change. Always refer to the implement owner's manual for the appropriate ballast requirements.  

 

Specifications


Compare the specifications of up to 4 models

Key Specs 1570-terraincut-mower
Current Model
Engine Manufacturer/model3TNV88C
Engine PowerGross PS: 37.4 hp
27.5 kW
Fuel tank capacity16 U.S. gal.
60.6 L
Mower deck Size60, 72 in.
152, 183 cm
Blade tip speed18,000 fpm
5,486 m/min
TransmissionHydrostatic 2WD, optional full time or on demand 4WD
Speed range0-12 mph
0-19.3 km/h
Drive wheels23x10.5-12, Optional 23x8.5-12
Caster wheelsFlat free, 11x4-5
Warranty24 months
Engine
Manufacturer/model3TNV88C
Power
Gross
PS, 37.4 hp
27.5 kW
Rated engine rpm3,000 rpm
CylindersThree
Displacement100.2 cu in.
1.64 L
Maximum torqueAt 1,950 rpm, 80.4 lb-ft
109 Nm
InjectionDirect
Fuel typeDiesel (B20 compatible)
Fuel tank capacity16 U.S. gal.
60.6 L
CoolingLiquid
Cooling capacity8 U.S. qt
7.6 L
Air cleanerDual element dry type
Air restriction indicatorStandard
Charging systemAutomotive type
Alternator, amp75 amp
Battery12 V
Drivetrain
TransmissionHydrostatic 2WD, optional full time or on demand 4WD
Speed and direction controlTwo-pedal foot
Cruise controlOptional
Hi/Lo rangeNo, single speed transmission
Travel speed
Speed range0-12 mph
0-19.3 km/h
Hi forward
Lo forward
Hi reverse
Lo reverse
4-wheel drive

Differential lock
Final drives
PTO
PTO clutch
PTO drive output
Hydraulics
TypeOpen center
Pump capacity5.1 U.S. gpm
19.3 L/min
Spool valveFront lift, standard
Lift cylindersTwo
Steering
TypeHydraulic cylinder
Turns lock-to-lock2 maximum, 1.5 minimum
Brakes
TypeInternal wet disk
Individual turn brakesStandard
Master brakeStandard, locking
Buyer's notes
Tires
Drive wheels23x10.5-12, Optional 23x8.5-12
Steering18x8.5-8 (2WD), 18x8.5-10 (4WD)
Weight transfer
Dimensions
Wheelbase49.2 in.
125 cm
Ground clearance6.5 in.
16.5 cm
LengthLess mower deck, 86.7 in.
220.2 cm
Overall widthWith 23x10.5 tires, 51.7 in.
131.3 cm
ROPSStandard (folding)
ROPS certification2-POST: OSHA 1928; Canadian Std.: CSA-352; 4-POST: SAE J2194; EU Standard: 86/298/EEC; ISO 21299:2009
Overall height with ROPS82.7 in.
210 cm
Overall height with ROPS folded58 in.
147 cm
Shipping weightNet weight, 2wd without mower or fuel, 1,800 lb
816 kg
Net weight, 4wd without mower or fuel, 1,960 lb
889 kg
Mower decks
ConstructionOne-piece stamped steel; 7-Iron PRO
Deck thickness7 gauge
0.18 in.
4.6 mm
Size60, 72 in.
152, 183 cm
Deck offsetYes
Cutting height1-6 in.
2.54-15.24 cm
Belt tensioningSpring loaded
Blade tip speed18,000 fpm
5,486 m/min
Caster wheelsType
Flat free
Size
11x4-5
Front anti-Scalp rollersYes, gauge wheels
Rear anti-scalp rollersYes, gauge wheels
Shipping weight
Mower deck (rear discharge)
Cutting width62, 72 in.
157, 183 cm
Cutting height1-6 in.
2.54-15.2 cm
Caster wheelsType
Flat free
Size
11x4-5
Shipping weight

Accessories and Attachments

Auxiliary Hydraulics

Hydraulic weight transfer adjustment wheelHydraulic weight transfer adjustment wheel
#

The hydraulic weight transfer attachment allows transferring weight of an implement to drive wheels for improved traction in slippery or hilly areas. The hydraulic weight transfer adjustment wheel is located on the control panel to the right of the operator for easy use. It is adjustable from full-off to full-on while on the go.

#
#

One-spool auxiliary hydraulic kit for use on snow blowers for chute rotation or blade/broom angling:

  • Allows operating implements that require one hydraulic function, such as for angling a snow blower chute or changing the angle of a front blade

 

Cold Start Packages

Heater
Engine coolant heaterEngine coolant heater
Coolant heater adapterCoolant heater adapter

Heater adapter attaches to the engine cylinder block. Heater plugs into a 120-V electrical outlet to warm the engine for fast cold weather starts. It has a 400 W rated output.

Drive Wheels And Tires

Dual wheel shownDual wheel shown

Order this kit to convert the traction unit to have 23 x 8.5-12-in. dual drive wheels.

This kit includes spacers and hardware required to convert traction unit to dual drive wheels. Tires and rims are not included.

NOTES:
1) 62-in. (158-cm) rear-discharge mower is not compatible with the dual wheel conversion kit.
2) Dual wheel conversion kit cannot be used in conjunction with the MCS 600 Hydraulic High-Dump Material Collection System.

Hydraulics

Lighting

Beacon lightBeacon light
#

This light is required by some governmental agencies and on some worksites. It provides increased visibility of the unit when in operation and mounts to the top of the rollover protective structure (ROPS).

NOTE: The beacon light mounts to the top right ROPS tube on two-post ROPS and four-post ROPS assemblies.
Front mower with four-post ROPS and front worklightsFront mower with four-post ROPS and front worklights
Front worklightsFront worklights

Front worklights mount to the top frame of the four-post ROPS.

Mirrors

Gives the operator a view to the rear at a quick glance.

Miscellaneous

Left-hand front tie-down bracket illustrationLeft-hand front tie-down bracket illustration
Right-hand front tie-down bracket illustrationRight-hand front tie-down bracket illustration

Front tie-down brackets provides great locations to secure a front mower when hauling. The tie-downs are left- and right-hand, mounted to the lift-arm receivers. They are designed specifically for the John Deere 1500 Series TerrainCut™ Front Mowers. Tie-downs are useful for any hauling application to make securing the vehicle easier and better:

  • TCU38441 left-hand front tie-down bracket
  • TCU38442 right-hand front tie-down bracket

Key features include:

  • Constructed with 0.25-in. (6.4-mm) A36 steel plate
  • Designed specifically for the John Deere 1500 Series TerrainCut Front Mowers
  • Simple bolt-on design
  • Does not interfere with mower deck
Left-hand front tie-down bracket illustrationLeft-hand front tie-down bracket illustration
Right-hand front tie-down bracket illustrationRight-hand front tie-down bracket illustration

Front tie-down brackets provides great locations to secure a front mower when hauling. The tie-downs are left- and right-hand, mounted to the lift-arm receivers. They are designed specifically for the John Deere 1500 Series TerrainCut™ Front Mowers. Tie-downs are useful for any hauling application to make securing the vehicle easier and better:

  • TCU38441 left-hand front tie-down bracket
  • TCU38442 right-hand front tie-down bracket

Key features include:

  • Constructed with 0.25-in. (6.4-mm) A36 steel plate
  • Designed specifically for the John Deere 1500 Series TerrainCut Front Mowers
  • Simple bolt-on design
  • Does not interfere with mower deck

Double-Spool Auxiliary Hydraulic Kit - BTC10529

The cruise control kit maintains desired speed without foot pressure.

The reverse alarm attachment is available for improved safety and for those who require an alarm in reverse speeds to satisfy safety regulations and governmental bid requirements.

#
#

This emblem attaches to the ROPS for transporting on public roads. Available on cab and open-station models.

Drive tires are available for field installation.

Drive tires are available for field installation.

Vehicle enclosure kit illustrationVehicle enclosure kit illustration
Vehicle enclosure kit installed illustrationVehicle enclosure kit installed illustration

This vehicle enclosure kit limits the amount of debris buildup around the transmission and engine, making daily maintenance and service fast and easy.

The vehicle enclosure kit is shipped with a 62-in. (157-cm) or 72-in. (183-cm) rear-discharge deck from the factory as standard equipment and is dealer installed. It may be ordered as an attachment for 62-in. (157-cm) or 72-in. (183-cm) 7-Iron™ PRO Commercial Side-Discharge Decks.

Roll Over Protection System (Rops)

Four-post ROPSFour-post ROPS
Four-post ROPSFour-post ROPS

The four-post ROPS consists of two front posts, welded top and bottom assemblies, and a molded roof.

Tire Chains

Tire chains provide additional traction for the machine.

Tire chains provide additional traction for the machine.

Weights

Wheel weightWheel weight

One or two weights can be installed on each drive wheel if extra traction is desired.

 

Wheel weights will fit on both the 1400 and 1500 Series II Front Mowers.

 

Mounting hardware (one) for attaching 72-lb (34-kg) starter weight and (two) 50-lb (22.7-kg) cast-iron weights on 26-in. (66-cm) tire

WeightWeight

The 42-lb (19-kg) Quik-Tatch weight can be used to counterbalance a heavy front or rear attachment and/or provide greater stability, especially when operating on hills.

 

Weights are constructed of cast iron and weigh approximately 42 lb (19 kg) each.

Rear weight mounting bracket partsRear weight mounting bracket parts
Rear weight mounting bracket with weightsRear weight mounting bracket with weights

Allows operator to mount ballast weights for additional traction (four R66949 or UC13263 42-lb (19-kg) Quik-Tach weights are recommended for snow blower applications).

Windshield

This front windshield mounts to the four-post ROPS.

  • Compatible with:
    • 1500 Series TerrainCut™ Front Mowers
    • 1400/1500 Series II Front Mowers

Reviews

1

1 reviews

Rating Snapshot

12
8
0
1
4
1
1
4

Good ideal until it goes wrong

1/5

This machine has been at the dealer for repairs more hours than we have had it in the field (shut down) . Maybe lack of knowledge in the service dept to repair, I would not recommend this machine.

Pros

Cons

MisterSmitty

From: Pittsburgh, pa

Length of Ownership: 1yearOrLonger

Usage Frequency: Daily

Level of Expertise: Expert

1
2
5